T56 Programmer Universal programmer

Name: T56 Programmer Universal programmer
SKU: 1070794959

Saddar, Karachi

3 days ago

Details

Is DeliverableNo

Price46,500

TypeOther

ConditionNew

Description

T56 Programmer Support 28,468 IC Devices SIZE:12.9cm x 8.5cm x 2.9cm Super performance Super speed Super small portable Cool appearance Low power consumption Super stability 1. Chip support: Base the TL866II Plus add Support for Nor Flash / NAND Flash / EMMC TSOP48 / TSOP56 / BGA48 / BGA63 / BGA64 / BGA100 / BGA153 / BGA162 / BGA169 / BGA221 Initial version: IC supported: 20900+ pcs 2. Programmer parameters (1). 32-bit MCU 200MHZ + Xilinx SP6 FPGA structure, USB2.0 HS 480MHZ transmission (2). 56 pin full drive IO design. All pins have a maximum operating frequency of 50MHZ and high reliability. (3). Stable and reliable 8Pins in-circuit programming interface, the wire Lehgth is more than 30CM, and it can communicate reliably at 25MHZ. 25 series / EMMC in-circuit programming with a maximum clock frequency of 40MHZ-50MHZ (4). VCC voltage 1.2-6.5V 64 levels adjustable, VPP voltage 6.5-25V 64 levels adjustable. IO communication signal voltage continuously adjustable 1.2V-3.6V VCC 120MA-320MA overcurrent protection continuously adjustable VPP 120MA overcurrent protection. (5). Power consumption: 5V <;;;;;;;;500MA. All chips do not need external power supply. It can be connected to an external power supply 5V-5.5V 500MA for multipile programming. The external power can be powered by a cell phone charger can be seen everywhere. The programmer has multiple protections for the external power supply: overvoltage protection / reverse connection protection / overcurrent protection / low voltage prompt. (6). Write EMMC Speed: 12MB/s-25MB/s Reading EMMC speed: 14MB/s-45MB/s is 2-5 times faster than similar programmers. (This is important for large-capacity chips, 64GB EMMC chips, If 10MB/s (the average programmer cannot reach 10MB/s) reading takes 6400 seconds, T56 can usually reach more than 20MB/s, as long as about 3000 seconds) Ability to handle extremely high speeds, meaning that programmer hardware has greater stability at lower speeds (7). Open self-test function, self-check each VPP/VCC /GND/IO 3. EMMC programming function special introduction (1). The most functions EMMC programmer, which can perform one-key mass production operation on EMMC (also can be programmed with 4 machines in one computer) Load project files, load all parameter settings at once, and directly program. Read and write speeds up to 12MB / s-45MB / s (2). EMMC function introduction 2.1: Analysis function : analyze the content of the original chip, and display the following results: Display chip manufacturing information Visual display of chip usage up to 8 partitions Each partition shows whether it is write protected, can be read, can be rewritten or deleted Shows whether the entire chip is temporarily or permanently write protected Show whether the chip is password protected Show whether the chip uses a 32-bit security authentication code to write to the RPMB. Show other important parameters of ECSD/CSD/CID You can also read the ECSD / CSD / CID file into this programmer to enter the load analysis Can also perform some general analysis on ECSD files read by other programs 2.2: Read/write functions (all functions can be completed with one-key) Read CID / CSD / ECSD. Clear full-chip temporary write protection before programming Clear temporary write protection groups before programming Delete chip before programming Blank Check the chip before programming Programming 32-bit authentication key Perform chip password verification Partiton Config Read and Programming to BOOT1 Read and Programming to BOOT2 Read and Programming to RPMB Read and Programming to GP1 Read and Programming to GP2 Read and Programming to GP3 Read and Programming to GP4 Read and Programming user data (User Area) Setting temporary write protection groups Setting permanent write protection groups Setting password (or reset password) Programming ECSD Programming CSD Automatically verify all the above operations after Programming (3) . ISP in-circuit programming function 3.1 Ultra-high stability ISP in-circuit programmi

Related ads